Cylinder kit -PINASCO Zuera Ø57,5mm SRV reed valve 135cc- Vespa V50, PV125, ET3, PK50, PK80, PK125
- Description
- Reviews (0)
- Add a review
Description
The Pinasco 135cc ZUERA cylinder, named after a Spanish race track, comes out of the box with a rather sporty 125/185 head angle. This already puts it above the Polini Evolution 1, which obviously was the inspiration for the design here.
Unlike other cylinders, the openings of the overflow channels in the cylinder base are already open. This requires the adjustment of the fan channel on the stator housing (explained in the manual supplied with the cylinder). The cylinder base has a diameter of 61.3mm, therefore it is not necessary to enlarge the cylinder base bore in the engine housing.
The one-piece exhaust is manufactured with about 66% width in the direction of durability. We would assume that the Zuera 135SS, due to its more sporty exhaust geometry, is slightly above the Polini Evolution I in terms of performance.
Due to the angles of the overflow channels facing the exhaust, the Zuera 135SS also supports exhaust systems that like to reach into higher rpm regions.
Technical details
- Bore 57.5mm
- Stroke 51mm
- Capacity 135ccm
- 5 overflow channels
- One-piece outlet, trapezoidal, chord 38.5mm ≈ 66%
- Outlet stud M8(not included, we recommend Piaggio)
- perforated outlet flange 52mm (as exhaust gasket we recommend BGM)
- cylinder base gaskets three pieces in 0,1mm
- cylinder base Ø61,3mm (suitable for Piaggio)
- cast iron piston 169gr, one piston ring 1mm
- piston pin safety device type G, 1mm
- cylinder head 8-fold screwed (stud bolt + 4pcs. M8x25mm)
- spark plug 14mm, long thread, recommendation B9ES, B10ES
- spark plug position, central
- ignition timing 17° (recommendation from Pinasco)
- control angle 125°/185° with a pinch dimension of 1.0mm and 51mm stroke
the pinch edge of 1.0 – 1.1mm can be adjusted using the 3 0.1mm cylinder base gaskets supplied. When it comes to cylinder head gaskets, Pinasco keeps a discreet distance, also with regard to the sealing and the connection to the exhaust. An exhaust gasket suitable for the Zuera SS135 is not included, nor are the required exhaust studs.
The PK125 exhaust gasket from Piaggio fits the flange. However, the SS135 outlet is 31mm x 27mm. This means that the PK125 exhaust gasket will not fit here due to the smaller inner diameter. Alternatively you can use the BGM exhaust gasket. With this variant, however, you must extend the hole in the gasket by a few millimeters.
The bottom line is that Pinasco has created a sporty cylinder that offers good performance with little effort. Whether with SHB19, Polini CP carburetors and Piaggio or Polini Banana or with a Keihin 28 and a Franz – the Pinasco SS135 can be used in a performance range from moderate to sporty with the right environment of carburetor and exhaust. intake port and connecting rubber
- piston, incl. piston pin, piston ring and fuses
- fastening material cylinder head
- gasket set cylinder base
- plug for the cylinder cover
NOTE: The frame cut-out in the area of the intake port may have to be be modified/extended
- Vespa (Piaggio) Vespa 50 L (V5A1T)
- Vespa (Piaggio) Vespa 50 N (V5A1T)
- Vespa (Piaggio) Vespa 50 (V5A1T, 1963)
- Vespa (Piaggio) Vespa 50 S (V5A1T, 1964)
- Vespa (Piaggio) Vespa 50 Special (V5A2T)
- Vespa (Piaggio) Vespa 50 Special Elestart (V5A3T)
- Vespa (Piaggio) Vespa 50 Special (V5B1T)
- Vespa (Piaggio) Vespa 50 Special Elestart (V5B2T)
- Vespa (Piaggio) Vespa 50 Special (V5B3T)
- Vespa (Piaggio) Vespa 50 Special Elestart (V5B4T)
- Vespa (Piaggio) PK 50 XL2 (V5N1T)
- Vespa (Piaggio) PK 50 XL2 HP (V5N2T)
- Vespa (Piaggio) PK 50 SS (V5S1T)
- Vespa (Piaggio) PK 50 XLS (V5S2T)
- Vespa (Piaggio) Vespa 50 Sprinter (V5SS2T, -1975)
- Vespa (Piaggio) Vespa 50 SR (V5SS2T, 1975-)
- Vespa (Piaggio) PK 50 (V5X1T)
- Vespa (Piaggio) PK 50 S (V5X2T)
- Vespa (Piaggio) PK 50 S Lusso (V5X2T)
- Vespa (Piaggio) PK 50 XL (V5X3T)
- Vespa (Piaggio) PK 50 XL Rush (V5X4T)
- Vespa (Piaggio) PK 50 N (V5X5T)
- Vespa (Piaggio) PK 50 XL2 (V5X3T)
- Vespa (Piaggio) PK 80 S (V8X5T)
- Vespa (Piaggio) Vespa 90 (V9A1T)
- Vespa (Piaggio) Vespa 90 Super Sprint (V9SS1T, SS90)
- Vespa (Piaggio) Vespa 125 Nuova (VMA1T)
- Vespa (Piaggio) Vespa 125 Primavera (VMA2T)
- Vespa (Piaggio) Vespa 125 ET3 (VMB1T)
- Vespa (Piaggio) PK 125 ETS (VMS1T)
- Vespa (Piaggio) PK 125 (VMX1T)
- Vespa (Piaggio) PK 125 S (VMX5T)
Reviews (0)
- There are no reviews yet.
You may also like…
CDI -PIAGGIO- Vespa PX (- 05/2011), Rally200 (Ducati), PK XL, ET3, Lambretta (Ducati)
50 L (V5A1T) €32,78 Incl. VAT + Add to cart
PARMAKIT 19 mm Advance Crank Vespa PK/Special/ET3/Primavera
Engine
€190,91 €171,82 Incl. VAT
+ Add to cart
Fuel pump -MIKUNI- delivery rate 20 l/h
50 XL €40,91 Incl. VAT + Add to cart
Related Products
Cluch castle nut -BGM PRO- Vespa Largeframe models (-1995) – clutch nut
Engine €2,95 + Add to cart
GASKET SET VESPA PX TSV D.66 C/57
Cosa 125
€19,24 €16,44 Incl. VAT
+ Add to cart
Polini Exhaust Vespa 300 GTS
Exhaust €496,88 Incl. VAT + Add to cart
BGM Manual Choke + Cable 150cm, universal
50 L (V5A1T) €14,83 Incl. VAT + Add to cart
Be the first to review “Cylinder kit -PINASCO Zuera Ø57,5mm SRV reed valve 135cc- Vespa V50, PV125, ET3, PK50, PK80, PK125”