Crankshaft -MAZZUCCHELLI Racing (rotary valve)- Vespa PV125, ET3 125, PK80 S, PK125 S (Ø=19mm cone)
- Description
- Reviews (0)
- Add a review
Description
In order to achieve higher speeds, one should reach for the racing shaft. The extended intake timing results in a much freer engine revs. This measure is especially noticeable with high-revving cylinders.
The quality of the crankshafts is very good and so they resist even the highest revs. Especially for the higher capacity engines from 125cc they are an optimal supplement to extend the usable speed range of racing cylinders without spitback in the lower speed range.
These engines offer both, a decent torque over the whole speed range and a free coasting without the engine running out of air on inclines.
Bearings | |
---|---|
sizes: | 15x19x20mm |
Gudgeon pins | |
diameter: | 15 mm |
Crankshafts | |
stroke: | 51 mm |
thread rotor side: | M10x1,5 right-hand thread |
thread drive side: | M12x1,25 right-hand thread |
diameter crankwebs: | 87 mm |
width crankwebs: | 38 mm |
diameter bearing seat rotor side: | 25 mm |
diameter bearing seat drive side: | 17 mm |
diameter oil seal seat rotor side: | 19 mm |
diameter oil seal seat drive side: | 22.7 mm |
full circle crankshaft: | |
rotary valve crankshaft: | |
length rotary crankweb: | 180 mm |
Vespa V50, PV – intake timing for short rotary surface (22mm) (°): | 151 |
Vespa PK XL2, ETS – intake timing for long rotary surface (28mm) (°): | 160 |
Vespa PK XL2, ETS – intake timing for long rotary surface (37mm fully modified) (°): | 173 |
crankcase has to be milled: | |
engine casing has to be modified: | |
Connecting rods | |
length connecting rod: | 97 mm |
thickness connecting rod: | 4.6 mm |
diameter small end connecting rod eye: | 19 mm |
lubricating hole at small end bearing: | no |
diameter crankpin: | 20 mm |
lubricating hole at crankpin bearing: | notch |
crankpin shims: | yes |
FITS :
- Vespa (Piaggio) PK 80 S (V8X5T)
- Vespa (Piaggio) Vespa 90 (V9A1T)
- Vespa (Piaggio) Vespa 90 Super Sprint (V9SS1T, SS90)
- Vespa (Piaggio) Vespa 125 Nuova (VMA1T)
- Vespa (Piaggio) Vespa 125 Primavera (VMA2T)
- Vespa (Piaggio) Vespa 125 ET3 (VMB1T)
- Vespa (Piaggio) PK 125 ETS (VMS1T)
- Vespa (Piaggio) PK 125 (VMX1T)
- Vespa (Piaggio) PK 125 S (VMX5T)
Reviews (0)
- There are no reviews yet.
You may also like…
Crankshaft -POLINI (rotary valve) 51mm stroke, 97mm con-rod- Vespa PV125, ET3 125, PK80 S, PK125 S (Ø=19mm cone)
Engine €133,78 Incl. VAT + Add to cart
Related Products
Hi-speed Variator 9 rollers Vespa 200/250/300
GTS 300 4T €117,82 Incl. VAT + Add to cart
Piston -BGM PRO 177/187cc- Vespa PX125, PX150, Cosa125, Cosa150, GTR125, TS125, Sprint Veloce (VLB1T 0150001-) – Ø=63.0mm (A)
Engine €59,09 Incl. VAT + Add to cart
BGM Manual Choke + Cable 150cm, universal
50 L (V5A1T) €11,72 Incl. VAT + Add to cart
Bearing driveshaft selector box 28,3×42,3×9,5 mm for Vespa 125 VNA/VNB/GT 1°/Super 1°/150 VBA/VBB/VGLA/B/GL/Sprint 1°/Super 1°
ACMA €17,26 Incl. VAT + Add to cart
Be the first to review “Crankshaft -MAZZUCCHELLI Racing (rotary valve)- Vespa PV125, ET3 125, PK80 S, PK125 S (Ø=19mm cone)”