Main jet set -BGM PRO for Dellorto (type: 4576) SI- (140-162) – (140-142-145-148-150-152-155-158-160-162)
- Description
- Reviews (0)
- Add a review
Description
The main jet of the SI carburettor determines how much petrol is made available to the so-called premix or pre-foaming. The higher the capacity and the higher the litre capacity, the greater the need for spraying. The available range is from 90-160. 102 main jet has a bore of 1.02mm, and thus provides less fuel than 104 main jet (1.04mm bore). That means the bigger the nozzle is numbered the richer the mixture becomes.
function nozzle block SI
The main nozzle should not be considered isolated, because it is only responsible to keep the fuel level in the nozzle block area on a sufficient level. Due to the vacuum at the atomizer tube the fuel is sucked in from the nozzle block. The fuel flowing into the nozzle block from below is limited to a maximum by the main nozzle. Air is also sucked in from above, whereby a fuel/air mixture is already formed inside the carburettor (mixing tube). This pre-mixture lets the mixture burn more effectively since it can be atomized more finely than pure gasoline.
If the HmainLairKcorrectionDnozzle is dimensioned the pre-mixture becomes too rich or too lean. If the HLKD is e.g. very large (190), the premix receives a high proportion of air whereby a disproportionately large main nozzle is required so that the engine runs properly even under full load. However, the result is often a mixture that is too rich under partial load and the scooter bucks. Nevertheless it can die off under full load in the upper speed range because the fuel level drops below the delivery height of the exhaust tube and the fuel supply is cut off. Often this phenomenon is tried to cure by mounting a so-called float chamber spacer. It is assumed that the float chamber will be sucked empty and therefore the engine dies off.
Normally a change of the air jet is more effective because the spacers increase the filling level in the carburettor, but they also provide a higher level in the nozzle block area, so that the premix can no longer work properly. Under certain circumstances gasoline can then also run (flood) from the atomizer directly into the engine. The real problem is therefore not a too small volume of the float chamber but a tuning of the HVACD.
A frequent problem which causes very large main nozzles is a modification of the air filter or the replacement by an intake funnel. In the original filter, a hole is often drilled into the filter bottom above the nozzles to allow a better flow to the HVAC. This measure usually improves the pre-foaming, but with heavily modified engines it can lead to a too low negative pressure in the nozzle block. As a result, the fuel level drops below the threshold of the atomizer/petrol outlet tube and the engine is only insufficiently supplied with mixture. Apart from a too lean full load operation, which usually no larger main nozzle can catch, it can come in extreme cases also to a complete stop of the gasoline delivery.
No more extreme is this problem when using air funnels. Here, with a used HVAC of 160, main nozzles are often used far beyond size 150. Here, too, problems often occur in the partial load range because the system of fuel delivery and premixing is out of balance. An adapted, smaller main air correction nozzle also helps to bring the main nozzle requirement back into an appropriate range.
TIP
The main nozzle for a new tuning of the engine is always as large as to throttle off under full throttle (four-stroke). Starting from this, reduce the main nozzle until the engine takes full throttle and turns off without jerking. A swallowing at throttle acceptance or a four-stroke in the partial load range is then carried out afterwards by an appropriate selection of the secondary nozzle, gas slide and possibly another mixing tube.
The HLKD (main air correction nozzle) is selected sufficiently small for most engines with 160.
FITS :
- Vespa (Augsburg) Vespa 150 T/4 (type 332, 3-speed) (VGLA1T)
- Vespa (Augsburg) Vespa 150 T/4 (type 332, 4-speed) (VGLB1T)
- Vespa (Augsburg) Vespa 150 T/4 (type 202, VGLA1T)
- LML 125 (2 stroke)
- LML 125 Deluxe (2 stroke)
- LML 125 DLX (2 stroke)
- LML 125 Stella (2 stroke)
- LML 125 Via Toscana
- LML 150 Belladonna (2 stroke)
- LML 150 Belladonna RV (2 stroke)
- LML 150 DLX (2 stroke)
- LML 150 Star (2 stroke)
- LML 150 Via Toscana (2 stroke)
- Vespa (Motovespa) Vespa 125 CL (engine 9CL)
- Vespa (Motovespa) Vespa 150 CL (engine 9NC)
- Vespa (Motovespa) Vespa 200 DS (engine 9DS)
- Vespa (Motovespa) Vespa 200 DN (engine 9DN)
- Vespa (Motovespa) PX 125 Iris (engine 99M)
- Vespa (Motovespa) PX 150 Iris (engine 75M)
- Vespa (Motovespa) PX 200 Iris (engine 73M)
- Vespa (Motovespa) PX 200 Iris (engine 76M)
- Vespa (Motovespa) PX 200 Iris (engine 77M)
- Vespa (Motovespa) PX 125 T5 Sport Elestart (engine 108M)
- Vespa (Motovespa) PX 125 T5 Sport (engine 98M)
- Vespa (Motovespa) TX 200
- Vespa (Piaggio) P 80 X (V8X1T, -1983)
- Vespa (Piaggio) PX 80 E FL (V8X1T, 1983-)
- Vespa (Piaggio) PX 80 E FL Elestart (V8X1T, 1984-1990)
- Vespa (Piaggio) Vespa 150 (VB1T)
- Vespa (Piaggio) Vespa 150 (VBA1T)
- Vespa (Piaggio) Vespa 150 (VBB1T)
- Vespa (Piaggio) Vespa 150 (VBB2T)
- Vespa (Piaggio) Vespa 150 Super (VBC1T)
- Vespa (Piaggio) 125 PX E FL (2017-, ZAPM74100)
- Vespa (Piaggio) 150 PX E FL (2017-, ZAPM74200)
- Vespa (Piaggio) 125 PX E FL (2016-, ZAPM74100) special edition “70 years”
- Vespa (Piaggio) 150 PX E FL (2016-, ZAPM74200) special edition “70 years”
- Vespa (Piaggio) Vespa 150 GL (VLA1T)
- Vespa (Piaggio) Vespa 150 Sprint (VLB1T)
- Vespa (Piaggio) Vespa 150 Sprint Veloce (VLB1T)
- Vespa (Piaggio) Vespa 125 GTR (VNL2T)
- Vespa (Piaggio) Cosa 150 CL (VLR1T)
- Vespa (Piaggio) Cosa 150 CLX (VLR1T300)
- Vespa (Piaggio) Cosa 150 FL (VLR2T)
- Vespa (Piaggio) P 150 X (VLX1T, -1980)
- Vespa (Piaggio) PX 150 E FL (VLX1T, 1984-1997)
- Vespa (Piaggio) PX 150 E (VLX1T, 1981-1983)
- Vespa (Piaggio) Vespa 125 (VNA1T)
- Vespa (Piaggio) Vespa 125 (VNA2T)
- Vespa (Piaggio) Vespa 125 (VNB1T)
- Vespa (Piaggio) Vespa 125 (VNB3T)
- Vespa (Piaggio) Vespa 125 (VNB4T)
- Vespa (Piaggio) Vespa 125 (VNB5T)
- Vespa (Piaggio) Vespa 125 (VNB6T)
- Vespa (Piaggio) Vespa 125 Super (VNC1T)
- Vespa (Piaggio) Vespa 125 GT (VNL2T)
- Vespa (Piaggio) Vespa 125 TS (VNL3T)
- Vespa (Piaggio) Cosa 125 CL (VNR1T)
- Vespa (Piaggio) Cosa 125 CLX (VNR1T300)
- Vespa (Piaggio) Cosa 125 CLX (VNR1T301)
- Vespa (Piaggio) P 125 X (VNX1T, -1983)
- Vespa (Piaggio) PX 125 T5 (VNX5T)
- Vespa (Piaggio) Vespa 180 Rally (VSD1T)
- Vespa (Piaggio) Vespa 200 Rally (VSE1T, Femsa)
- Vespa (Piaggio) Vespa 200 Rally (VSE1T, Ducati)
- Vespa (Piaggio) Cosa 200 CL (VSR1T)
- Vespa (Piaggio) Cosa 200 CLX (VSR1T300)
- Vespa (Piaggio) Cosa 200 FL (VSR1T301)
- Vespa (Piaggio) P 200 E (VSX1T, -1980)
- Vespa (Piaggio) PX 200 E FL (VSX1T, 1984-1997)
- Vespa (Piaggio) PX 200 E (VSX1T, 1981-1983)
- Vespa (Piaggio) PX 125 E FL (ZAPM09300, 1998-2000)
- Vespa (Piaggio) PX 125 E FL (ZAPM09302, 2001-)
- Vespa (Piaggio) PX 150 E FL (ZAPM09400, 1998-2000)
- Vespa (Piaggio) PX 150 E FL (ZAPM09401, 2001-)
- Vespa (Piaggio) PX 200 E FL (ZAPM18, 1998-)
Reviews (0)
- There are no reviews yet.
You may also like…
Air filter -PIAGGIO- Vespa Dellorto SI20/20D, SI24/24E, SI24/24H (long version, with hole above main air jet)
Cosa 125 €13,03 Incl. VAT + Add to cart
DELLORTO MAIN JET (SIZE 115-140) FOR SI20-20/SI24-24/SI26-26
Carburator Parts
€4,54 €4,08 Incl. VAT
Choose Options
DELL’ORTO SI 24-24 E Carburator for Vespa PX125-200 / Rally 180-200/Cosa 125-200
Cosa 125 €71,94 Incl. VAT + Add to cart
DELLORTO Gasket repair kit SI20/20 & SI24/24 Vespa PX 80/125/150/200
Carburator Parts €5,87 Incl. VAT + Add to cart
Related Products
Cluch castle nut -BGM PRO- Vespa Largeframe models (-1995) – clutch nut
Engine €2,95 + Add to cart
ATHENA Top end gasket set Vespa GTS300 ’08-’17
Engine €34,39 Incl. VAT + Add to cart
Crimp terminal – male spade connector 2.8mm Ø=0.5-1.0mm²- DIN 46244 – 10 pcs
Frame €1,32 Incl. VAT + Add to cart
Flywheel SIP Touren for Vespa 125 GTR 2°/TS 2°/150 Sprint V 2°/Super 2°/200 Rally 2°/PX80-200/PE/Lusso/Cosa
Cosa 125
€105,55 €95,00 Incl. VAT
+ Add to cart
Be the first to review “Main jet set -BGM PRO for Dellorto (type: 4576) SI- (140-162) – (140-142-145-148-150-152-155-158-160-162)”